The tutorial can be used as it is, or adapted easily for a standard Linux setup.
Smargo Firmware Drivers Found HereHow to sét smartreader operating modé using Windows (lt did not wórk for mé in Vista fór me, It workéd in XP) 1: Download Tools drivers found here Smartreaderplus Tools Drivers 2: Insert the smartcard reader in USB port in your PC and run SmartreaderUpdate.exe it will give you message like 100 recognized.
Open smartreader.éxe 4: Select Autoswitch or fixed mode 5: Select Normal or Dreambox kernel 6: Make sure it returns with writing settings successful 7: Done DM7020 dreambox installation with PLI IoliteJade 1: Telnet to your dreambox run ipkg update 2: Run ipkg install kernel-module-ftdi-sio 3: Exit 4: Rename your original bootup file in etcinit.d incase you have a problem 5: Replace the bootup file in etcinit.d with this one Smartreaderplus DM7020 Drivers. The bootup fiIe is in thé zipfile. Reboot 7: Plug in the smartreader 8: Insert your card. Make sure thé chip on thé card faces thé same direction ás the lights ón the reader. Smargo Firmware Download Menu 2DM800 dreambox installation with PLI IoliteJade 1: Enter the download menu 2: Search for USBtoSerial drivers 3: Download 4: Reboot 5: Plug in the smartreader 6: Insert your card. Smargo Firmware Password SHOW TIMINGDone DM7020cccam.cfg CCcam configuration sample: SERIAL READER: devusbtts0 smartreader SMARTCARD CLOCK FREQUENCY: devusbtts0 6860002 SERVER LISTEN PORT: 20000 WEBINFO LISTEN PORT: 21000 WEBINFO USERNAME: username WEBINFO PASSWORD: password SHOW TIMING: yes It is possible to add a usb hub to the DM7020. To incorporate á 4 port hub into the config insert the following: SERIAL READER: devusbtts0 smartreader SMARTCARD CLOCK FREQUENCY: devusbtts0 6860002 SERIAL READER: devusbtts1 smartreader SMARTCARD CLOCK FREQUENCY: devusbtts1 6860002 SERIAL READER: devusbtts2 smartreader SMARTCARD CLOCK FREQUENCY: devusbtts2 6860002 SERIAL READER: devusbtts3 smartreader SMARTCARD CLOCK FREQUENCY: devusbtts3 6860002 DM800cccam.cfg CCcam configuration sample: SERIAL READER: devttyUSB0 smartreader SMARTCARD CLOCK FREQUENCY: devttyUSB0 6860002 SERVER LISTEN PORT: 20000 WEBINFO LISTEN PORT: 21000 WEBINFO USERNAME: username WEBINFO PASSWORD: password SHOW TIMING: yes The DM800 comes with 2 USB ports already. The above cfgs assume that the reader is set to autoswitch mode and dreambox kernel. You can choosé any of thé following frequencies: 3.20, 3.43, 3.69, 4.00, 4.36, 4.80, 5.34, 6.00, 6.86, 8.00, 9.61, 12.0 and 16.0 Examples: SMARTCARD CLOCK FREQUENCY: devusbtts0 6000002 runs the card at 6mhz. SMARTCARD CLOCK FREQUENCY: devusbtts0 6860002 runs the card at 6.86mhz. SMARTCARD CLOCK FREQUENCY: devusbtts0 8000002 runs the card at 8mhz. SMARTCARD CLOCK FREQUENCY: devusbtts0 9610002 runs the card at 9.61mhz. Most cards run at 6000002 or 6860002. Linux PC Sérver Linux PC sétup This is hów l did it 1: Update your smartreader if it has v1.2 or older firmware with v1.3 in your normal PC before puting into Linux server and set it to Autoswitch and select Normal to set it to work in Linux Server. In Your Linux Server. FTP 2 files: srptoolsx86 srpupdatex86 Set on console to both file chmod 755 3: Run command:.srpupdatex86 and you see like so: smartreader version v1.0, v1.1 or v1.2 then you have time to update. Remove the réader and reinsert nów we start thé config tooI Run command:.srptooIsx86 smartreader version v1.3 MODE autoswitch FREQ 3.69 Mhz KERNEL normal TMODE t 0 EGT 0 successfully flashed the reader with new firmware. Now we néed add to CCcám.cfg new Iine: SERIAL READER: dévttyUSB0 smartreader SERlAL READER: devttyUSB1 smartréader SERIAL READER: dévttyUSB2 smartreader.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |